CLS_REF:

This test refines a plate by class.

• cls_ref commands
• cls_ref data
• cls_ref log
• cls_ref output
• cls_ref pictures

DORIS:

This test calculates joint displacements on a plate for a load case derived from temperature.

• doris commands
• doris data
• doris log
• doris output

LS_TP:

This tests a longitudinaly stiffened system of four triangular plates. This is physically equivalent to the test ls_qp.

• ls_tp commands
• ls_tp data
• ls_tp log
• ls_tp output

LS_QP:

This tests a longitudinaly stiffened, square plate.

• ls_qp commands
• ls_qp data
• ls_qp log
• ls_qp output

MP:

This tests four plates with more than four nodes.

• mp commands
• mp data
• mp log
• mp output

NOT_CONVEX:

This tests the error message for plates which are not convex.

• not_convex commands
• not_convex data
• not_convex log
• not_convex output

PLA_CHK:

This tests a quad and two triangles which should be the same.

• pla_chk commands
• pla_chk data
• pla_chk log
• pla_chk output

PLA_OFF:

This tests plate offsets.

• pla_off commands
• pla_off data
• pla_off log
• pla_off output

PLA_PATC:

This tests several plates which form a rectange.

• pla_patc commands
• pla_patc data
• pla_patc log
• pla_patc output

PLA_REFN:

This tests the use of a plate reference node.

• pla_refn commands
• pla_refn data
• pla_refn log
• pla_refn output

PLA_WT:

This test checks the weights of stiffners added to plates.

• pla_wt commands
• pla_wt data
• pla_wt log
• pla_wt output

PLA_TEMP:

This tests temperature in a plate.

• pla_temp commands
• pla_temp data
• pla_temp log
• pla_temp output

PSEUDO_Q1:

This tests the loads from a plate get passed to the pseudo plate element.

• psuedo_q1 commands
• psuedo_q1 data
• psuedo_q1 log
• psuedo_q1 output

PSEUDO_Q4:

This tests the is similar to PSUEDO_Q1. Here the original plate is made up of four triangular plated. The test is the check loads from the original plate get passed to the pseudo plate element.

• psuedo_q4 commands
• psuedo_q4 data
• psuedo_q4 log
• psuedo_q4 output

QP:

This is a basic rectangular plate and a beam which should give the same answers. It is used for comparison with the stiffened plate tests (lp_qp).

• qp commands
• qp data
• qp log
• qp output

REF_FE:

This test checks a bracket with a free edge.

• ref_fe commands
• ref_fe data
• ref_fe log
• ref_fe output
• ref_fe pictures

REF_HOLE:

This test refines a square plate with a hole in it three times: once by specifying an edge, once by specifying two edges, and once refining all edges.

• ref_hole commands
• ref_hole data
• ref_hole log
• ref_hole output
• ref_hole pictures

REF_QUAD:

This test refines a square plate three times: once by specifying an edge, once by specifying a box in space, and finally by specifying an element.

• ref_quad commands
• ref_quad data
• ref_quad log
• ref_quad output
• ref_quad pictures

TP:

This test should give the same results as qp except that the quad is changed to four symmetric triangles.

• tp commands
• tp data
• tp log
• tp output

TP_TEST:

This tests sp_plate elements.

• tp_test commands
• tp_test data
• tp_test log
• tp_test output

TS_QP:

This is test of a rectangular plate stiffened transversely.

• ts_qp commands
• ts_qp data
• ts_qp log
• ts_qp output

ZP:

This is test of the -rel option on the PLATE command.

• zp commands
• zp data
• zp log
• zp output