• General Changes
• Supported Machines
• Report Control Changes
• New Reports
• Connector Changes
• Roll Damping Changes
• Piece Changes
• Time Synthesis Changes
• Defaults and Paramaters
• What No Longer Works
• What Answers Will Change

General Changes:

• The report given with the PLATE STRESS command in the stuctural post-processing menu has been changes to also report the principle stresses and the angle of S1 from the element X axis.
• A new plate summary report, VERTEX, has been added to the PLATE_SUM command and the format of the PROPERTIES report has been changed. Click here to see the documentation or here to see an example.
• A new POINT summary report, N_COINCIDENT, has been added to the POINT_SUM command. Click here to see the documentation or here to see an example.
• You can get information about several new things with the &ELEMENT string function. Click here to see the documentation.
• One can now have three reference points when defining a point. Click here to see the documentation.
• In the past, there was a maximum on the number of items that could be selected for the VIEW and STATSTICS commands. These restrictions have been removed. Also, the reportes generated with these commands "look better" and also contain most of the description.
• One can now define a limits on the percentage full of a compartment. When the percentage is outside this range, no free surface correction will be applied. Click here to see the documentation.
• One can now define the deviation of the wind from the mean and use it in a time domain simulation. Click here to see the documentation or here to see an example.
• The options -WAVE_RUN, -PERI_USE, and -FACT_CONV have been removed from the G_PRESSURE and A_PRESSURE commands in the Hydrodynamics Menu and added to the &DESCRIBE BODY command and the option -TPRE_FACT has been removed from the documentation. Click here to see the documentation. Also, a new value &STATUS BODY has been added to report the "body settings". Click here to see the documentation.
• One can now look at deflection and ratios during an animation. Click here to see the documentation. Here to see an example. here to look at a deflection "movie". here to look at a ratio "movie".
• One can now change the places which will be searched when either USE_VES or USE_MAC is specified. Click here to see the documentation.
• The concept of "functions" has been around since the beginning of MOSES, but was never documented. Since they are used extensively in the macros that we supply, we finally documented them. Click here to see the documentation.
• A new option, -CDR_VONMISES has been added to the PLATE_POST command that controls wheter the Von Mises stress or the principle stresses are used in computing the CDRs for a plate. Click here to see the documentation.
• The stability macros, stak_ok and kg_allow have been changed to make more checks and to only display checks where criteria have been specified. Also, the -EQUI option has been remove and -NO_EQUI has been added. Click here to see the documentation.

Supported Machines:

• WINDOWS running on AMD/Intel X86
• LINUX running on AMD/Intel X86
• LINUX running on AMD/Intel X86_64
• SOLARIS running on SPARC
• SOLARIS running on AMD/Intel X86_64
• MAC OS X running on PowerPC
• MAC OS X running on Intel X86

Report Control Changes:

• A new option, -MAG_DEFINE, has been added to the POINTS and CONFORCE commands in the PRCPOST menu, This gives the user the ability to define how the "magnitude" column on the reports is computed from the basic information. Click here or here to see the documentation or here to see an example.
• A new internal menu, &TABLE, has been created. This allows one to build "good looking" HTML tables directly in MOSES. Click here to see the documentation or here to see an example.
• The reporting in the Disposition Menu has been changed. Two new option -MAG_USE and -BOTH have been added and the -HEADING option can now be used on more commands. Finally, the STORE command has options that allow one to produce "good looking" HTML tables. Click here to see the documentation or here to see an example.
• Three new options, -CONT_ENTRY, -SET_DATE and -NAME_FIGURE, have been added to the &DEVICE command. Click here to see the documentation.

• The documentation for the REL_MOTION command has been changed to correctly show that one can have more than two relative motion points. Click here to see the documentation. Click here to see the documentation.

New Reports:

• A report on the relative wave/point velocity has been added to the POINTS command in the Process Post-Processing Menu. Click here to see the documentation or here to see an example.
• A new group of things for which one can get &NAMES is NG_S_CASES (Non Converged Structural Solution Cases). Also, one can now issue &STATUS NAMES, to get not only a list of groups but a brief description of them. Click here, here, or here to see the documentation.
• A new summary, RESTRAINT_SUM, has been added. Click here to see the documentation.
• A new summary, PROPERTIES. has been added to then COMPART_SUM command. Click here to see the documentation.

Roll Damping Changes:

The "Tanaka Damping" has been totally changed. In the past it was defined in the Hydrodynamics Menu. Today it is either an attrribute of a piece or a load group.

• The commands A_TANAKA, V_TANAKA, G_TANAKA, E_TANAKA, and I_TANAKA are no longer valid commands in the Hydrodynamics Menu.
• The -FM_TANAKA and -TM_TANAKA are not honored on either the &PARAMTER, A_PRESSURE, or G_PRESSURE. They have been replaced with -TANAKA on either the &DESCRIBE PIECE command, or &DEFAULT. Click here to see the documentation.
• A new command #TANAKA has been created which allows one to create a load group which computes Tanaka damping. Click here to see the documentation.
• Finally, if you try to import an old hydrodynaic database, you will get a lot of errors because you can no longer import the Tanaka data. You can fix this by changing the old command:

  
      I_TANAKA LBARGE COW -PERIOD 25 20 19 18 17 16 15 14.5 14 13.5 13 12.5 12 11.5 \
                                  11 10.5 10 9.5 9 8.5 8 7.5 7 6.5 6 5.5 5 4.5 4 3  \             
                          -ANGLE 5 10 15 20 25 30 35                                \
                          -FM_TANAKA 1 -TM_TANAKA 8
  

  to

      #TANAKA  -PERIOD 25 20 19 18 17 16 15 14.5 14 13.5 13 12.5 12 11.5 \
                       11 10.5 10 9.5 9 8.5 8 7.5 7 6.5 6 5.5 5 4.5 4 3  \             
               -ANGLE 5 10 15 20 25 30 35 
     

Connector Changes:

• The -DAMPING option for flexible connector classes is now obsolete and has been dropped from the documentation. It has been replaced with three options -X_DAMPING, -Y_DAMPING, and -Z_DAMPING. With these options one can now define a nonlinear dashpot and for GSPR type connectors you can define a different one for each translational degree of freedom. Click here to see the documentation.
• GSPR, LMU, and FOUNDATION connectors can now have "PY" curves defined for all three translational degrees of freedom. The old option -CONEPY has been replaced with three new ones: -X_PY, -Y_PY, and -Z_PY. The old option has been removed from the documentation but still works. Click here to see the documentation or here to see an example.
• The -FRICTION option for has changed for GSPR and FOUNDATION classes. If one has lateral springs defined, then it behaves as before, but without springs it ask opposite the relative, horizontal velocity. Click here to see the documentation.
• A new option, -PISTON, has been added to most flexible element classes. This models a hydraulic pistion which can be used to limit the tension. Click here to see the documentation, and here to see an example.

Pieces Changes:

• The option -DD_MULT defines a table of draft / water depth multipliers. If one uses this option, then the effects of shallow water on current force is automatically accounted for. Click here to see the documentation.
• The option -TANAKA can be specified to define a multipler for the Tanaka damping. Click here to see the documentation.
• The option -AMASS can be used estimate the added mass for a piece. Click here to see the documentation.

Time Synthesis Changes:

Defaults and Parameters:

What No Longer Works:

• Two inactive options on the &REP_SEL command: -AISC and -LRFD have been deleted.
• The values for MIN_EVENT and MAX_EVENT have been removed from the -MOVIE option of &PICTURE. Click here to see the documentation.
• One can no longer do graphics to the screen when MOSES is not interactive. This has never worked correctly, but now it is impossible.
• The column definitions in the Disposition Menu for the POINTS command have changed due to the change described above. Any macros that you may have written that extract information from the POINTS command will have to be changed.

What Answers Will Change:

• The computation of the added mass for a #PLATE has been changed. It is now computed according to DNV Classification Notes 30.5. As a result, the -AMCPLATE option of &PARAMTER is now ignored.
• The results of STAB_OK and KG_ALLOW macros may change. This is due to a change in how "downflooding" was computed. In the past, only the Weather Tight points were considered. Now, the Non Weather Tight ones are used for checking intact cases and both Weather Tight and Non Weather Tight ones are used for damaged cases.
• Due to the changes discussed above, you will not be able to import a hydrodynamic database without changing it as described above.
• The options -FM_TANAKA and -TM_TANAKA are no longer valid.
• The commands A_TANAKA, V_TANAKA, G_TANAKA, E_TANAKA, and I_TANAKA are no longer valid commands in the Hydrodynamics Menu.
• The RAO convergence has been changed and this will slightly change frequency domain results.
• The "effective length" for joint crushing has been changed to correspond to RP2A 21st edition.
• The default for the SCF computation for tubular joints has been changed from K&S to EFTHYMIOU.